Category Archives: Car Amplifiers

Kenwood have put their reputation building car amplifiers that no-nonsense reliability and superior sound quality. The compact KAC-8404 4-channel amplifier features a rugged cast aluminum housing more than 40% smaller than its predecessor, but it would be to pump still 50 watts RMS into 4 channels – ideal for enhancing the performance of the front and rear speakers in your system. Or you can use the amplifier 2-channel mode, the bridge and a few U-boats with 180 watts RMS without any effort on your car’s electrical system.

Built adapt-in high-and low-pass filter output of the amplifier, so you get the best possible sound from your speakers or subwoofer combo, while the variable bass boost you can use up to 18 dB bass boost dial, if you want to fatten the sound.

The front panel controls you can tweak the sound easily and conveniently front-side connections make installation a breeze. A signal-dependent and speaker inputs allow these amps to connect up to factory radios that do not have preamp outputs.

The Kenwood is 4-channel amplifier has two stereo amplifiers used in a case which can be used not only in a 4-channel configuration, but can also be bridged and a 2-channel or 3-channel configuration . The amplifier is rated at 180 watts x 2 at 4 ohms 2-channel mode and 50 watts x 2/180 watts x 1 into 4 Ohms 3-channel mode.

BUY KENWOOD KAC-8404 NOW AT A SPECIAL PRICE WITH DISCOUNT!

The amplifier uses guarantee a MOS-FET power transistors providing thermal stability and efficient switching speed performance and reliability.

be a fixed 18dB of bass boost at 40Hz for amplifier B (back) deals only. There is no bass boost for amplifier A (front). You can independently switch amplifier A (front) and B amplifier (rear) from stereo to mono mode. When Mono, the signal is from the left channel input only used to go off. An amplifier (front) and B (back) have controls in each separate line-level RCA inputs with independent gain (input sensitivity). The input sensitivity controls accept an input signal of 200mV to 5.0 volts.

The Kenwood KAC-8404 features a brushed aluminum cover that hides all its controls. This is a very clean look and protects the amplifier controls are not changed accidentally. The cover is held in place by two Allen screws. An Allen key provided to remove the cover.

The KAC-8404 has built-in high pass and low pass filter crossovers. The high pass crossover’s slope 12 dB/octave and is continuously variable from 50Hz to 200Hz and can independently for the A (front) and B (Rear) channels are controlled. The low-pass crossover slope is 12 dB/octave continuously variable from 50Hz to 200Hz and can independently for the A (front) and B (Rear) channels are controlled. The amplifier can be operated simultaneously at full range for both A (front) and B (Rear) channels.

BUY KENWOOD KAC-8404 NOW AT A SPECIAL PRICE WITH DISCOUNT!

He KAC-8404 will use a 4-channel speaker input terminals. This feature makes it easier, an amplifier to add a factory or a radio receiver without preamp outputs. You do not need to connect the remote input wire, if you use the speaker input, because the performance of the amplifier is set to “On” and “off” as an amplifier input signal from the unit detects high-level input.

When the device is turned on to the amp turned on, the Power indicator lights red. This will disappear with the amplifier and void if the amplifier is in protection mode. The amplifier has a blue LED light on the top of the amplifier when the amplifier is powered lights.

BUY KENWOOD KAC-8404 NOW AT A SPECIAL PRICE WITH DISCOUNT!

There are two fans and two holes on the back of the amplifier to help dissipate heat and to ensure cool, reliable operation. Make sure these vents or fans, if you block the install amplifier.

The amplifier features protection circuits that are off the amplifier at the following events to the amplifier and to protect the speakers:

• Speaker output to ground
• Speaker cable short circuits
• Malfunctions and DC is sent to speaker output
• Internal temperature too high
• The loss of the base of the head unit or amplifier

Kenwood has a history of high-quality car audio. This is a review of the KAC-7204-model. For between $ 90 on Amazon and $ 130 at local retailers, you can purchase the new KAC-7204 amplifier system, but we decided to help your decision.

This is a powerful system. This was my first observation at the hearing of the amplifier projection. A total of 500 watts each channel sends a really great sound boost on four dour Ford vehicle that we are on pre-amp and level control outpout you demonstrated a very good feeling of the option to choose where you want to make adjustments decibels . I opted for the amplifier and are medium in my dashboard.

BUY KENWOOD KAC-7204 NOW AND GET OUR DISCOUNT!

There is also a bridge option for a subwoofer if you have a really full bass sound from your system preference. Here is where I made my first negative remarks made. After a minute or so, I have to check a heat. I think this model is much hotter than I feel it is normal for a sound provider. The transduction is not insulated properly, because the feeling of heat on the unit was enough to force my hand away for a moment. That was my biggest concern in product reviewed.

The amplifier is appealing and elegant in design. The black case offers a stylish finish.

To continue on aesthetics, the blue lighting looks a very good atmosphere to go for a night. At thirteen inches wide, setting the unit is a simple process. The blue is soothing and not a hindrance, as some other amplifier systems I have seen in the car.

Overall, this Kenwood amplifier has enough power. The look and design is very nice and would make good fit in almost any car. If it is running hot is a problem for you as it has me going, you can see this model in favor of another product.

BUY KENWOOD KAC-7204 NOW AND GET OUR DISCOUNT!